en

Product categories

CONSTRUCTION SYSTEMS

CERAMIC ADHESIVES

JOINT FILLING MIXTURES

REPAIR AND MOUNTING MIXTURES

WATERPROOFING MIXTURES

HEAT INSULATION MATERIALS

PRODUCTS BASED ON GYPSUM

CEMENT-BASED PLASTERS

PRODUCTS BASED ON LIME STONE

LIME PRODUCTS

PVA GLUES

PAINTING PRODUCTS

DECORATIVE FACADE COATINGS BASED MINERAL

PRIMERS

SURFACE PROTECTION AND SURFACE CLEANING

SURFACE SYSTEMS

CEMENT BASED SURFACE HARDENING MATERIALS

SOLVENT-FREE EPOXIDE BASED MATERIALS

SELF-LEVELLING FLOOR COMPOUND

ADMIXTURE SYSTEMS

CONCRETE ADMIXTURES

MIXED ADDITIVES

CONCRETING ASSISTANT MATERIALS

SUPPORTING MATERIALS FOR GRINDING

AUXILIARY PRODUCTS TO CONSTRUCTION OF UNDERGROUND

"MA Tem" super spot cleaner

"MA Tem" super spot cleaner

Product consumption calculator


Preorder


Print


Product description

Product containing specific chemical substances, used for cleaning of different stains that are hard to remove.

Fields of Application

This product can be applied in the following areas:

  • Cleaning of facing tiles contaminated with oil stains;
  • Easy cleaning of similar stains remained on the facing tiles while they are bonded;
  • Cleaning of surfaces contaminated with hard-removable stains, such as alcoholic and alcohol-free drinks, coffee, oil, ink, shoe polish, lipstick, rust, Flo-Master, etc.
  • Cleaning of stains on varnished and non-varnished surfaces, granite, normal and uneven ceramics, kotto and acid-resistant facing materials

Advantages

  • Easily cleans stains on the facing stone surfaces;
  • Easily cleans stains that are hard to remove, such as coffee, oil, ink, shoe polish, lipstick, rust, Flo-Master, etc.

Instruction procedures

Preparation of mixture. Depending on the kind of stain the product can be mixed with water at 1/5 or 1/10 ratios.

Application. The cleaning work using  МА Tem  mixed with water at the above ratios can be conducted in two methods:

Manual cleaning: Spread the МА Sem product to approximately 2 m2 part of the area to be cleaned with a brush. Wait for 2-3 minutes, then clean it rubbing with rag. Fill the dirty water formed on the ground to bucket using sponge. Wash the rag and sponge with clean water. Clean the whole surface on the same way. After completion of the cleaning work, reuse the MA Sem product prepared by being mixed with less water in the areas where dirt remains. Then rub the whole surface damping it with large amount of water, and wait until it is totally dry. To remove hard and heavy stains, use the МА Sem keep the product on the surface for a longer period of time without mixing it with water.

Dry cleaning and cleaning with vacuum equipment:  Spread the МА Sem product to approximately 4 m2 part of the area to be cleaned. Wait for 2-3 minutes, then put strong washing rag in the lower part and start cleaning using the equipment. Collect the dirty water formed on the ground using the vacuum equipment. Clean the whole surface on the same way. After completion of the cleaning work, reuse the MA Sem product prepared by being mixed with less water in the areas where dirt remains. Dampen the whole surface with large amount of water, then remove the collected water using the vacuum equipment and wait it to dry.

Recommendations. If in the application of the МА Sem  product, the environmental temperature is less than +50C and more than +300C,  required temperature should be provided. The product should not be used in hot (more than +300C), rainy and windy weather conditions. After use all appliances and tools should be cleaned with water.

Consumption 

3-5 liter of the cleaner allows cleaning of 100 m2 surface (without mixing with water).

Shelf Life and storage

The product can be stored during 12 months in unopened sacks in dry conditions

Warnings

  • taking into consideration that МА Tem is a complex mixture, immediately rinse it with water in case of contact with skin or eyes;
  • do not add any substances not indicated in the application procedures;
  • parameters indicated above were received on the basis of laboratory tests conducted in the ambient conditions of +230C±20C temperature and 50% + 5% humidity. Depending on the ambient conditions these parameters may be changed.

Warranty and technical support

  • Information indicated in the technical specifications is based on scientific and practical knowledge;
  • “Matanat А" company is responsible only for the product quality;
  • Except for the works carried out under the guidance of the company specialists, “Мatanat  А" company bears no responsibility for any problems that may occur as a result of improper use of the product by other users;
  • The company reserves the right to make changes to its product that may occur due to a scientific and technnological development;
  • For technical support or more information please do not hesitate to contact “Matanat А" company!

These products are used to

"MA Sem" ideal cement cleaner

"PROMATEKTOR" surface protector

Preorder