en

CONSTRUCTION SYSTEMS

DECORATIVE FACADE COATINGS BASED MINERAL

ADMIXTURE SYSTEMS

"FasNatural 100" powder mix for production of compound for decorative facing panels on building facades and decorative elements by means of moulding

"FasNatural 100" powder mix for production of compound for decorative facing panels on building facades and decorative elements by means of moulding

Product consumption calculator


Preorder


Terms of use

Print


Product description

Lime stone based, monocomponent powder product, resistant to frost, high temperatures, water and environmental impact, has high strength properties, used for production of decorative and facing stone composites. The product conforms to the requirements of the TS AZ 3143489-006-2010 technical specifications and GOST 9479-84 state standard.

Fields of Application

This product can be applied in the following areas:

  • Manufacture of stone panels (similar to facing panels manufactured from natural limestone) applied directly onto the surfaces lined with CPF (compressed polystyrene foam), EPF (extruded polystyrene foam), rock-wool (pressed mineral cotton panels) and polyurethane panels by plastering upon plastered building face walls built from concrete, limestone (construction stone), foamed concrete, and other stone kinds;
  • architectural works;
  • Laying of decorative stones onto the ground.

Advantages

  • Substitutes Aglay stone (natural facing limestone produced in Azerbaijan);
  • Does not absorb water;
  • Does not form cracks in frosty conditions;
  • Reduces loads on building faces by 11 times;
  • Cost effective;
  • The product has higher strength compared to natural stone;
  • Can be applied using both plaster machine and a trowel;

Application procedures

Preparation of the surface. Before application of the FasNatural product pay attention to the surfaces: they should be checked for strength, and free of residues deteriorating adhesive force. In case the FasNatural product is applied onto the heat insulating panels, these panels should be installed on even surfaces. The FasNatural product may be applied onto the masonry walls built from limestone (construction stone), foamed concrete, and other types of stone; in this case the surface first should be treated with primer, and plastered with Binmader prior to the product use. The FasNatural may be applied directly onto the concrete surfaces.

Preparation of the mixture. Carefully pour 25 kg of FasNatural product into 5.5 – 6.0 liters of clean water and wait 3 minutes, then mix using a mixer or any suitable hand tool till it is entirely homogeneous.

Application. Apply the prepared FasNatural mixture onto the building facade surface plastered with primer. Use trowel or special pumping equipment. The applied layer  thickness should be 1 cm maximum, and when applied onto CPF, EPF, and other panels installed on the building facade the thickness should be 0.5 cm. The FasNatural is applied onto the EPF and EPF panels by thin layer using trowel. Apply mesh onto the first layer before crust has been formed. Apply the second layer of the FasNatural product onto the mesh. After hardening of FasNatural product (in approximately 1 day) the grooves of required size should be cut using a special milling tool. The cut grooves should be filled with the FasNatural product using trowel, and then should be smoothed using special tool provided that the required groove depth necessary for decoration purposes is maintained. The surface should be polished after full hardening of FasNatural (in approximately 7 days). To renovate or repair the Aglay plates installed on the building facades the FasNatural mixture should be applied onto the surface by at least  3 mm thick layer using manual spray applicator gun.

The prepared mixture should be used within 80 minutes. To repair decorative stone composites the mixture should be cast in moulds. Depending on the ambient temperature within 24 hours the mould should be open and ready product should be removed from it. Besides, broken natural stone and other problems occurring on facades of ancient architectural monuments may also be restored using the FasNatural mixture.

Note: In case of lining building facade surfaces with the FasNatural mixture, if required, the surface may be polished again to the depth of 1 mm in 20 years.

Recommendations. If at the time of the FasNatural product application the ambient temperature exceeds the limits of +50C - +300C range, then the required temperature level should be provided. The product should not be used in warm (above +300C), rainy and windy weather conditions. After expiration of useful life the mixture in no case should be diluted with water or fresh powder mix. After use all hand tools and devices should be cleaned with water.

Consumption

The FasNatural powder mix consumption at 3 mm thick layer is 4.0-4.5 kg/m2, and at 5 mm thick layer is 7.0-7.5  kg/m2.

Shelf Life and Storage Method

The product can be stored during 12 months packed in original sacks in dry conditions on wooden racks, maximum 10 sacks per rack.

Warnings

  • taking into consideration that FasNatural is a cement based mixture enriched with chemical compounds, immediately rinse it with water in case of contact with skin or eyes;
  • do not add any substances not indicated in the application instructions;
  • parameters indicated above have been received on the basis of laboratory tests conducted in the ambient conditions of +230C±20C temperature and 50% + 5% humidity. Depending on the actual ambient conditions these parameters are subject to change.

Warranty and technical support

  • information indicated in technical specifications is based on scientific and experimental data;
  • Matanat А company is responsible for the product quality only;
  • with the exception of cases of works executed under the supervision of the company specialists, Мatanat  А company shall not be liable for any problems occuring due to improper use of the product by other persons;
  • the company reserves the right to make changes in its product in consequence of scientific-and-technical development;
  • for technical support and/or more information please do not hesitate to contact the Matanat А company!